Action Pak DC Input, Bipolar Output, Field Configurable Isolator

AP4382
DC Input, Bipolar Output, Field Configurable Isolator

TECHNICAL SPECIFICATION ( AP4382)
Input		Voltage Input (field configurable)
	Full Scale Range:	10mV to 100V
	Impedance:	>100K Ohms
	Overvoltage:	400 Vrms, max (Intermittent)
		264 Vrms, max (Continous)
Current Input (field configurable)
	Full Scale Range:	1mA to 100mA
	Impedance:	20 Ohms, typical
	Overcurrent:	170mA rms, max
	Overvoltage:	60VDC
Common Mode (Input to Ground):		1500VDC, max
Zero and Span Range
	Zero Turn-Up:	0 to 50% of full scale range
	Span Turn-Down:	100 to 50% of full scale range
Output	Voltage Output
	Output:	-10 to 10V, -5 to 5V
	Impedance:	<10 Ohms
	Drive:	10mA, max (1K Ohms min. @ 10V)
LED Indication (green)
	Input Range >110% input:	8Hz flash
	<0% input:	4Hz flash
Accuracy Including Linearity, Hysteresis
	<20mV/2mA:	±0.35% of full scale, typical, 0.5%, max
	>20mV/2mA:	±0.1% of full scale, typical, 0.2%, max
Response Time (10-90%)		200 mSec., typical
Stability (Temperature)		±0.025% of full scale/°C, typical, ±0.05%/°C, max
CMRR	DC to 60Hz:	120dB
Isolation (Input to Output)		1500 VDC between input, output and power
ESD Susceptibility		Meets IEC 801-2, Level 2 (4KV)
Humidity (Non-Condensing)
	Operating:	15 to 95% (@ 45°C)
	Soak:	90% for 24 hours (@ 65°C)
Temperature Range
	Operating:	-15 to 60°C (5 to 140°F)
	Storage:	-25 to 70°C (-13 to 158°F)
Power	Consumption:	3W typical, 5W max
	Standard:	selectable 120/240VAC, ±10%, 50-60Hz
	Optional:	9 to 30VDC, inverter isolated
Weight		0.60lbs
Agency Approvals		CSA certified per standard C22.2, No. M1982 (File No.LR42272-54).
		UL recognized per standard UL508 (File No. E150323).

Diagnostic LED
The AP4382 is equipped with a dual function LED signal monitor. The green, top-mounted LED indicates line power and input signal status. Active line power is indicated by an illuminated LED. If the input signal is 10% above the full scale range, the LED will flash at 8Hz. Below 0%, the flash rate is 4Hz.

Configuration
The factory preset input is 4-20mA and the output is -10 to 10V, as shown in Figure 1. The supply power is configured for 120 VAC operation. For other I/O ranges, remove the four base screws and case to access the I/O card.

WARNING: Do not change switch settings with power applied. Severe damage will result!

Calibration

Connect the input to a calibrated DC voltage or current source and apply power. Wait 1 hour for thermal stability before monitoring the voltage/ current output. Refer to PIN CONNECTIONS.
Set the calibrator to the desired minimum input and adjust the Zero, 20-turn, potentiometer for desired minimum output.
Set the calibrator to the desired maximum input and adjust the Span, 20-turn, potentiometer for desired maximum output.
Repeat steps 2 and 3 for best accuracy.

Last Updated Thursday, July 28, 2005

AP4382DC Input, Bipolar Output, Field Configurable Isolator

AP4382
DC Input, Bipolar Output, Field Configurable Isolator